John’s 360° Coatings® Application Instructions

The Avenger

1. Prep the surface of your vehicle. We recommend using a John’s 360° Coatings® Clay Mitt and soapy water to remove dirt and grime.
2. Inspect the surface for any scratches, swirls, haze and blemishes. To ensure a perfect application with an extra slick feel use John’s 360° Coatings Correction Compound to remove any defects.
3. Remove remaining wax, oil or grease. We recommend using John’s 360° Coatings Decon Spray.
4. Before mixing, shake the Activator and the Sealant separately.
5. Mix The Avenger using a 1:1 ratio of the Activator and Sealant. Shake well.
6. Apply 8-10 drops of formula in a line down the center of the microfiber sponge applicator. This will cover 2-3 square feet.
7. Immediately after applying the coating, use a clean microfiber cloth to polish it off. The coating may not feel slick when you first wipe it off, but this is because the product is still curing.
8. Repeat steps 5 and 6 until you have coated your entire vehicle.
9. Allow at least 3-4 hours for the product to cure, then polish the surface once more with a microfiber towel
10. For an extra sleek finish, wait 24 hours after applying The Avenger, then apply a layer of John’s 360° Coatings Speed Coat Ceramic Spray Sealant.

Super Blue 

Speed Coat

1. Spray onto a clean, damp microfiber cloth and onto the surface you are working on.
2. Gently wipe the surface with the cloth.
3. Before it dries, switch to a clean microfiber cloth and buff off. You may need to work in multiple small sections.
4. Repeat steps 1-3 until the entire surface is sealed, glossy, and streak-free.

Mint Ceramic Waterless Carwash

1. Spray onto a clean, damp microfiber cloth and onto the surface you are cleaning.
2. Gently wipe the surface with the cloth.
3. Before it dries, quickly switch to a clean microfiber cloth and buff off.
4. Repeat steps 1-3 until the entire surface is clean, sealed, glossy, and streak-free.

Decon Spray

1. Spray onto a clean, damp microfiber cloth and onto the surface you are cleaning.
2. Gently wipe the surface with the cloth.
3. Before it dries, quickly switch to a clean microfiber cloth and buff off.
4. Repeat steps 1-3 until the entire surface is clean, glossy, and streak-free.

Orange “No-Sling”

1. Apply a generous amount of the gel to an applicator.
2. Spread onto the surface evenly.
3. Allow 15-20 minutes for tires to dry to avoid slinging onto paint.
4. Repeat for enhanced gloss and shine.

Concentrated XP

1. Mix 1 ounce of Concentrated XP Foaming Soap with a gallon of water to activate.
2. Lather onto the surface of the vehicle to remove dirt and grime.
3. Rinse to reveal a clean, glossy surface.

Textile and Leather Guard

1. Spray generously onto the surface.
2. Gently work the product into the fibers of the textile using a soft-haired brush or microfiber cloth.
3. Let stand for 10 minutes.
4. Repeat steps 1 through 3 once more.

Metal X

1. Shake well.
2. Spray onto the surface you are cleaning.
3. Work onto the surface using a clean microfiber cloth, microfiber covered sponge, or soft-haired brush.
4. Rinse thoroughly with water or John’s 360° Coatings® Decon Spray to reveal a clean surface.

Water Spot Remover

1. Spray onto a clean microfiber cloth or microfiber covered sponge.
2. Gently wipe onto the surface.
3. Quickly clean the surface with John’s 360° Coatings® Decon Spray

Correction Compound

1. Shake well.
2. Apply 3-4 drops of Correction Compound to both a polishing pad and work area.
3. Set the polisher speed to 1000-1800 rpm and use light to medium pressure to work in until defects have been removed.
4. Wipe with a clean microfiber cloth.
5. Apply John’s 360° Coatings® Decon Spray to reveal any remaining defects.